Difference between revisions of "Miller theorem"

Miller theorem (for voltages)

Definition

The Miller theorem establishes that in a linear circuit, if there exists a branch with impedance Z, connecting two nodes with nodal voltages ­V₁ and V₂, we can replace this branch by two branches connecting the corresponding nodes to ground by impedances respectively Z/(1 − K) and KZ/(K − 1), where K = V₂/V₁. The Miller theorem may be proved by using the equivalent two-port network technique to replace the two-port to its equivalent and by applying the source absorption theorem.^[3] This version of the Miller theorem is based on Kirchhoff's voltage law; for that reason, it is named also Miller theorem for voltages.

Explanation

Miller theorem implies that an impedance element is supplied by two arbitrary (not necessarily dependent) voltage sources that are connected in series through the common ground. In practice, one of them acts as a main (independent) voltage source with voltage V₁ and the other – as an additional (linearly dependent) voltage source with voltage <math>V_2 = K{V_1}</math>. The idea of Miller theorem (modifying circuit impedances seen from the sides of the input and output sources) is revealed below by comparing the two situations – without and with connected an additional voltage source V₂.

If V₂ was zero (there was not a second voltage source or the right end of the element with impedance Z was just grounded), the input current flowing through the element would be determined, according to Ohm's law, only by V₁

<math>I_{in0} = \frac{V_1}{Z}</math>

and the input impedance of the circuit would be

<math>Z_{in0} = \frac{V_1}{I_{in0}} = Z.</math>

As a second voltage source is included, the input current depends on both the voltages. According to its polarity, V₂ is subtracted or added from/to V₁; so, the input current decreases/increases

<math>I_{in} = \frac{V_1 - V_2}{Z} = \frac{(1 - K)}{Z}{V_1} = {(1 - K)}{I_{in0}}</math>

and the input impedance of the circuit seen from the side of the input source accordingly increases/decreases

<math>Z_{in} = \frac{V_1}{I_{in}} = \frac{Z}{1-K}.</math>

So, Miller theorem expresses the fact that connecting a second voltage source with proportional voltage <math>V_2 = K{V_1}</math> in series with the input voltage source changes the effective voltage, the current and respectively, the circuit impedance seen from the side of the input source. Depending on the polarity, V₂ acts as a supplemental voltage source helping or opposing the main voltage source to pass the current through the impedance.

Besides by presenting the combination of the two voltage sources as a new composed voltage source, the theorem may be explained by combining the actual element and the second voltage source into a new virtual element with dynamically modified impedance. From this viewpoint, V₂ is an additional voltage that artificially increases/decreases the voltage drop V_z across the impedance Z thus decreasing/increasing the current. The proportion between the voltages determines the value of the obtained impedance (see the tables below) and gives in total six groups of typical applications.

The circuit impedance, seen from the side of the output source, may be defined similarly, if the voltages V₁ and V₂ are swapped and the coefficient K is replaced by 1/K

<math>Z_{in2} = \frac{{K}{Z}}{K-1}.</math>

Implementation

Most frequently, the Miller theorem may be observed in, and implemented by, an arrangement consisting of an element with impedance Z connected between the two terminals of a grounded general linear network.^[2] Usually, a voltage amplifier with gain of <math>A_V = K</math> serves as such a linear network, but also other devices can play this role: a man and a potentiometer in a potentiometric null-balance meter, an electromechanical integrator (servomechanisms using potentiometric feedback sensors), etc.

In the amplifier implementation, the input voltage V_i serves as V₁ and the output voltage V_o – as V₂. In many cases, the input voltage source has some internal impedance <math>Z_{int}</math> or an additional input impedance is connected that, in combination with Z, introduces a feedback. Depending on the kind of amplifier (non-inverting, inverting or differential), the feedback can be positive, negative or mixed.

The Miller amplifier arrangement has two aspects:

• the amplifier may be thought as an additional voltage source converting the actual impedance into a virtual impedance (the amplifier modifies the impedance of the actual element)
• the virtual impedance may be thought as an element connected in parallel to the amplifier input (the virtual impedance modifies the amplifier input impedance).

Applications

The introduction of an impedance that connects amplifier input and output ports adds a great deal of complexity in the analysis process. Miller theorem helps reduce the complexity in some circuits particularly with feedback^[2] by converting them to simpler equivalent circuits. But Miller theorem is not only an effective tool for creating equivalent circuits; it is also a powerful tool for designing and understanding circuits based on modifying impedance by additional voltage. Depending on the polarity of the output voltage versus the input voltage and the proportion between their magnitudes, there are six groups of typical situations. In some of them, the Miller phenomenon appears as desired (bootstrapping) or undesired (Miller effect) unintentional effects; in other cases it is intentionally introduced.

Applications based on subtracting V₂ from V₁

In these applications, the output voltage V_o is inserted with an opposite polarity in respect to the input voltage V_i travelling along the loop (but in respect to ground, the polarities are the same). As a result, the effective voltage across, and the current through, the impedance decrease; the input impedance increases.

Increased impedance is implemented by a non-inverting amplifier with gain of 0 < A_v < 1. The (magnitude of) output voltage is less than the input voltage V_i and partially neutralizes it. Examples are imperfect voltage followers (emitter, source, cathode follower, etc.) and amplifiers with series negative feedback (emitter degeneration), whose input impedance is moderately increased.

Infinite impedance uses a non-inverting amplifier with A_v = 1. The output voltage is equal to the input voltage V_i and completely neutralizes it. Examples are potentiometric null-balance meters and op-amp followers and amplifiers with series negative feedback (op-amp follower and non-inverting amplifier) where the circuit input impedance is enormously increased. This technique is referred to as bootstrapping and is intentionally used in biasing circuits, input guarding circuits,^[4] etc.

Negative impedance obtained by current inversion is implemented by a non-inverting amplifier with A_v > 1. The current changes its direction, as the output voltage is higher than the input voltage. If the input voltage source has some internal impedance <math>Z_{int}</math> or if it is connected through another impedance element, a positive feedback appears. A typical application is the negative impedance converter with current inversion (INIC) that uses both negative and positive feedback (the negative feedback is used to realize a non-inverting amplifier and the positive feedback – to modify the impedance).

Applications based on adding V₂ to V₁

In these applications, the output voltage V_o is inserted with the same polarity in respect to the input voltage V_i travelling along the loop (but in respect to ground, the polarities are opposite). As a result, the effective voltage across and the current through the impedance increase; the input impedance decreases.

Decreased impedance is implemented by an inverting amplifier having some moderate gain, usually 10 < A_v < 1000. It may be observed as an undesired Miller effect in common-emitter, common-source and common-cathode amplifying stages where effective input capacitance is increased. Frequency compensation for general purpose operational amplifiers and transistor Miller integrator are examples of useful usage of the Miller effect.

Zeroed impedance uses an inverting (usually op-amp) amplifier with enormously high gain A_v → ∞. The output voltage is almost equal to the voltage drop V_Z across the impedance and completely neutralizes it. The circuit behaves as a short connection and a virtual ground appears at the input; so, it should not be driven by a constant voltage source. For this purpose, some circuits are driven by a constant current source or by a real voltage source with internal impedance: current-to-voltage converter (transimpedance amplifier), capacitive integrator (named also current integrator or charge amplifier), resistance-to-voltage converter (a resistive sensor connected in the place of the impedance Z).

The rest of them have additional impedance connected in series to the input: voltage-to-current converter (transconductance amplifier), inverting amplifier, summing amplifier, inductive integrator, capacitive differentiator, resistive-capacitive integrator, capacitive-resistive differentiator, inductive-resistive differentiator, etc. The inverting integrators from this list are examples of useful and desired applications of the Miller effect in its extreme manifestation.

In all these op-amp inverting circuits with parallel negative feedback, the input current is increased to its maximum. It is determined only by the input voltage and the input impedance according to Ohm's law; it does not depend on the impedance Z.

Negative impedance with voltage inversion is implemented by applying both negative and positive feedback to an op-amp amplifier with a differential input. The input voltage source has to have internal impedance <math>Z_{int}</math> > 0 or it has to be connected through another impedance element to the input. Under these conditions, the input voltage V_i of the circuit changes its polarity as the output voltage exceeds the voltage drop V_Z across the impedance (V_i = V_z – V_o < 0).

A typical application is a negative impedance converter with voltage inversion (VNIC).^[5] It is interesting that the circuit input voltage has the same polarity as the output voltage, although it is applied to the inverting op-amp input; the input source has an opposite polarity to both the circuit input and output voltages.

Generalization of Miller arrangement

The original Miller effect is implemented by capacitive impedance connected between the two nodes. Miller theorem generalizes Miller effect as it implies arbitrary impedance Z connected between the nodes. It is supposed also a constant coefficient K; then the expressions above are valid. But modifying properties of Miller theorem exist even when these requirements are violated and this arrangement can be generalized further by dynamizing the impedance and the coefficient.

Non-linear element. Besides impedance, Miller arrangement can modify the IV characteristic of an arbitrary element. The circuit of a diode log converter is an example of a non-linear virtually zeroed resistance where the logarithmic forward IV curve of a diode is transformed to a vertical straight line overlapping the Y axis.

Not constant coefficient. If the coefficient K varies, some exotic virtual elements can be obtained. A gyrator circuit is an example of such a virtual element where the resistance R_L is modified so that to mimic inductance, capacitance or inversed resistance.

Dual Miller theorem (for currents)

Definition

There is also a dual version of Miller theorem that is based on Kirchhoff's current law (Miller theorem for currents): if there is a branch in a circuit with impedance Z connecting a node, where two currents I₁ and I₂ converge to ground, we can replace this branch by two conducting the referred currents, with impedances respectively equal to (1 + α)Z and (1 + α)Z/α, where α = I₂/I₁. The dual theorem may be proved by replacing the two-port network by its equivalent and by applying the source absorption theorem.^[3]

Explanation

Dual Miller theorem actually expresses the fact that connecting a second current source producing proportional current <math>I_2 = K{I_1}</math> in parallel with the main input source and the impedance element changes the current flowing through it, the voltage and accordingly, the circuit impedance seen from the side of the input source. Depending on the direction, I₂ acts as a supplemental current source helping or opposing the main current source I₁ to create voltage across the impedance. The combination of the actual element and the second current source may be thought as of a new virtual element with dynamically modified impedance.

Implementation

Dual Miller theorem is usually implemented by an arrangement consisting of two voltage sources supplying the grounded impedance Z through floating impedances (see Fig. 3). The combinations of the voltage sources and belonging impedances form the two current sources – the main and the auxiliary one. As in the case of the main Miller theorem, the second voltage is usually produced by a voltage amplifier. Depending on the kind of the amplifier (inverting, non-inverting or differential) and the gain, the circuit input impedance may be virtually increased, infinite, decreased, zero or negative.

Applications

As the main Miller theorem, besides helping circuit analysis process, the dual version is a powerful tool for designing and understanding circuits based on modifying impedance by additional current. Typical applications are some exotic circuits with negative impedance as load cancellers,^[6] capacitance neutralizers,^[7] Howland current source and its derivative Deboo integrator.^[8] In the last example (see Fig. 1 there), the Howland current source consists of an input voltage source V_IN, a positive resistor R, a load (the capacitor C acting as impedance Z) and a negative impedance converter INIC (R₁ = R₂ = R₃ = R and the op-amp). The input voltage source and the resistor R constitute an imperfect current source passing current I_R through the load (see Fig. 3 in the source). The INIC acts as a second current source passing "helping" current I_-R through the load. As a result, the total current flowing through the load is constant and the circuit impedance seen by the input source is increased. As a comparison, in a load canceller, the INIC passes all the required current through the load; the circuit impedance seen from the side of the input source (the load impedance) is almost infinite.

List of specific applications based on Miller theorems

Below is a list of circuit solutions, phenomena and techniques based on the two Miller theorems.

See also

• Miller effect
• Negative feedback amplifier
• Operational amplifier applications
• Bootstrapping

References

1. ↑ Miscellaneous network theorems
2. ↑ ^{2.0 2.1 2.2} EEE 194RF: Miller's theorem
3. ↑ ^{3.0 3.1} Miller's theorem
4. ↑ Working with High Impedance Op Amps AN-241
5. ↑ Nonlinear Circuit Analysis – An Introduction
6. ↑ Negative-resistance load canceller helps drive heavy loads
7. ↑ Impedance and admittance transformations using operational amplifiers by D. H. Sheingold
8. ↑ Consider the "Deboo" Single-Supply Integrator

External links

• Miller's theorem revisited
• New Results Related to Miller’s Theorem
• A network theorem dual to Miller's theorem
• Generalized Miller theorem and its applications

Further reading

Fundamentals of Microelectronics by Behzad Razavi
Microelectronic Circuits by Adel Sedra and Kenneth Smith
Fundamentals of RF Circuit Design by Jeremy Everardde:Millertheorem