Phase diagram
A phase diagram in physical chemistry, engineering, mineralogy, and materials science is a type of chart used to show conditions at which thermodynamically distinct phases can occur at equilibrium. In mathematics and physics, "phase diagram" is used with a different meaning: a synonym for a phase space.
Contents
Overview
Common components of a phase diagram are lines of equilibrium or phase boundaries, which refer to lines that mark conditions under which multiple phases can coexist at equilibrium. Phase transitions occur along lines of equilibrium.
Triple points are points on phase diagrams where lines of equilibrium intersect. Triple points mark conditions at which three different phases can coexist. For example, the water phase diagram has a triple point corresponding to the single temperature and pressure at which solid, liquid, and gaseous water can coexist in a stable equilibrium.
The solidus is the temperature below which the substance is stable in the solid state. The liquidus is the temperature above which the substance is stable in a liquid state. There may be a gap between the solidus and liquidus; within the gap, the substance consists of a mixture of crystals and liquid (like a "slurry").[1]
Types of phase diagrams
2D phase diagrams
The simplest phase diagrams are pressure-temperature diagrams of a single simple substance, such as water. The axes correspond to the pressure and temperature. The phase diagram shows, in pressure-temperature space, the lines of equilibrium or phase boundaries between the three phases of solid, liquid, and gas.
The curves on the phase diagram show the points where the free energy (and other derived properties) becomes non-analytic: their derivatives with respect to the coordinates (temperature and pressure in this example) change discontinuously (abruptly). For example, the heat capacity of a container filled with ice will change abruptly as the container is heated past the melting point. The open spaces, where the free energy is analytic, correspond to single phase regions. Single phase regions are separated by lines of non-analytical, where phase transitions occur, which are called phase boundaries.
In the diagram on the left, the phase boundary between liquid and gas does not continue indefinitely. Instead, it terminates at a point on the phase diagram called the critical point. This reflects the fact that, at extremely high temperatures and pressures, the liquid and gaseous phases become indistinguishable[2], in what is known as a supercritical fluid. In water, the critical point occurs at around Tc=647.096 K (1,164.773 °R), pc=22.064 MPa (3,200.1 psi) and ρc=356 kg/m³.[3]
The existence of the liquid-gas critical point reveals a slight ambiguity in labelling the single phase regions. When going from the liquid to the gaseous phase, one usually crosses the phase boundary, but it is possible to choose a path that never crosses the boundary by going to the right of the critical point. Thus, the liquid and gaseous phases can blend continuously into each other. The solid-liquid phase boundary can only end in a critical point if the solid and liquid phases have the same symmetry group[citation needed].
The solid-liquid phase boundary in the phase diagram of most substances has a positive slope; the greater the pressure on a given substance, the closer together the molecules of the substance are brought to each other, which increases the effect of the substance's intermolecular forces. Thus, the substance requires a higher temperature for its molecules to have enough energy to break out the fixed pattern of the solid phase and enter the liquid phase. A similar concept applies to liquid-gas phase changes.[4] Water, because of its particular properties, is one of the several exceptions to the rule.
- Other thermodynamic properties
In addition to just temperature or pressure, other thermodynamic properties may be graphed in phase diagrams. Examples of such thermodynamic properties include specific volume, specific enthalpy, or specific entropy. For example, single-component graphs of Temperature vs. specific entropy (T vs. s) for water/steam or for a refrigerant are commonly used to illustrate thermodynamic cycles such as a Carnot cycle, Rankine cycle, or vapor-compression refrigeration cycle.
In a two-dimensional graph, two of the thermodynamic quantities may be shown on the horizontal and vertical axes. Additional thermodymic quantities may each be illustrated in increments as a series of lines - curved, straight, or a combination of curved and straight. Each of these iso-lines represents the thermodynamic quantity at a certain constant value.
3D phase diagrams
It is possible to envision three-dimensional (3D) graphs showing three thermodynamic quantities.[5][6][7] For example for a single component, a 3D Cartesian coordinate type graph can show temperature (T) on one axis, pressure (P) on a second axis, and specific volume (v) on a third. Such a 3D graph is sometimes called a P-v-T diagram. The equilibrium conditions would be shown as a 3D curved surface with areas for solid, liquid, and vapor phases and areas where solid and liquid, solid and vapor, or liquid and vapor coexist in equilibrium. A line on the surface called a triple line is where solid, liquid and vapor can all coexist in equilibrium. The critical point remains a point on the surface even on a 3D phase diagram. An orthographic projection of the 3D P-v-T graph showing pressure and temperature as the vertical and horizontal axes effectively collapses the 3D plot into a 2D pressure-temperature diagram. When this happens, the solid-vapor, solid-liquid, and liquid-vapor surfaces collapse into three corresponding curved lines meeting at the triple point, which is the collapsed orthographic projection of the triple line.
Binary phase diagrams
Other much more complex types of phase diagrams can be constructed, particularly when more than one pure component is present. In that case concentration becomes an important variable. Phase diagrams with more than two dimensions can be constructed that show the effect of more than two variables on the phase of a substance. Phase diagrams can use other variables in addition to or in place of temperature, pressure and composition, for example the strength of an applied electrical or magnetic field and they can also involve substances that take on more than just three states of matter.
One type of phase diagram plots temperature against the relative concentrations of two substances in a binary mixture called a binary phase diagram, as shown at right. Such a mixture can be either a solid solution, eutectic or peritectic, among others. These two types of mixtures result in very different graphs. Another type of binary phase diagram is a boiling point diagram for a mixture of two components, i. e. chemical compounds. For two particular volatile components at a certain pressure such as atmospheric pressure, a boiling point diagram shows what vapor (gas) compositions are in equilibrium with given liquid compositions depending on temperature. In a typical binary boiling point diagram, temperature is plotted on a vertical axis and mixture composition on a horizontal axis.
A simple example diagram with hypothetical components 1 and 2 in a non-azeotropic mixture is shown at right. The fact that there are two separate curved lines joining the boiling points of the pure components means that the vapor composition is usually not the same as the liquid composition the vapor is in equilibrium with. See Vapor-Liquid Equilibrium for a fuller discussion.
In addition to the above mentioned types of phase diagrams, there are thousands of other possible combinations. Some of the major features of phase diagrams include congruent points, where a solid phase transforms directly into a liquid. There is also the peritectoid, a point where two solid phases combine into one solid phase during heating. The inverse of this, when one solid phase transforms into two solid phases during heating, is called the eutectoid.
A complex phase diagram of great technological importance is that of the iron-carbon system for less than 7% carbon (see steel).
The x-axis of such a diagram represents the concentration variable of the mixture. As the mixtures are typically far from dilute and their density as a function of temperature is usually unknown, the preferred concentration measure is mole fraction. A volume based measure like molarity would be unadvisable.
Crystal phase diagrams
Polymorphic and polyamorphic substances have multiple crystal or amorphous phases, which can be graphed in a similar fashion to solid, liquid, and gas phases.
In liquid crystal physics, phase diagrams are used in the case of mixing of nematogenic compounds to distinguish between the isotropic liquid phase, the nematic liquid phase.
See also
- CALPHAD (method)
- Congruent melting and incongruent melting
- Gibbs phase rule
- Glass databases
- Hamiltonian mechanics
- Schreinemaker's analysis
References
Cite error: Invalid <references> tag;
parameter "group" is allowed only.
<references />, or <references group="..." />External links
| 40x40px | Wikimedia Commons has media related to Phase diagram. |
- Iron-Iron Carbide Phase Diagram Example
- How to build a phase diagram
- Phase Changes: Phase Diagrams: Part 1
- Equilibrium Fe-C phase diagram
- Phase diagrams for lead free solders
- DoITPoMS Phase Diagram Library
- DoITPoMS Teaching and Learning Package- "Phase Diagrams and Solidification"ar:مخطط الطور
bs:Fazni dijagram bg:Фазова диаграма ca:Diagrama de fases cs:Fázový diagram de:Phasendiagramm el:Διάγραμμα φάσεων es:Diagrama de fase eo:Fazodiagramo fa:نمودار فازی fr:Diagramme de phase hr:Fazni dijagram id:Diagram fase is:Fasarit it:Diagramma di fase lv:Fāzu stāvokļa diagramma ms:Gambar rajah fasa nl:Fasediagram ja:相図 no:Fasediagram nn:Fasediagram pl:Wykres fazowy pt:Diagrama de fase ru:Фазовая диаграмма sk:Fázový diagram sl:Fazni diagram sr:Фазни дијаграм fi:Faasidiagrammi sv:Fasdiagram tr:Faz diyagramı uk:Фазова діаграма
zh:相图- ↑ Lua error in package.lua at line 80: module 'Module:Citation/CS1/Suggestions' not found.
- ↑ P. Papon, J. Leblond, and P.H.E. Meijer, The Physics of Phase Transition - Concepts and Applications Springer 1999.
- ↑ The International Association for the Properties of Water and Steam "Guideline on the Use of Fundamental Physical Constants and Basic Constants of Water", 2001, p. 5
- ↑ Chemistry: The Study of Matter, Forth Edition. Prentice Hall. pp. 266–273. ISBN 0-13-127333-7.
- ↑ Heat and Thermodynamics, Mark W. Zemansky, Richard H. Dittman, McGraw-Hill, 6th ed., 1981, Figures 2-3, 2-4, 2-5, 10-10, P10-1, ISBN 0-07-072808-9.
- ↑ Web applet: 3D Model: Water Phase Diagram.
- ↑ Web applet: 3D Phase Diagrams for Water, Carbon Dioxide and Ammonia. Described in A. Herráez, R.M. Hanson, and L. Glasser J. Chem. Educ. 86 (5), 566 (May 2009).
