Wien bridge oscillator
A Wien bridge oscillator is a type of electronic oscillator that generates sine waves. It can generate a large range of frequencies. The oscillator is based on a bridge circuit originally developed by Max Wien in 1891.[1] The bridge comprises four resistors and two capacitors. The oscillator can also be viewed as a positive gain amplifier combined with a bandpass filter that provides positive feedback.
The modern circuit is derived from William Hewlett's 1939 Stanford University master's degree thesis. Hewlett figured out how to make the oscillator with a stable output amplitude and low distortion.[citation needed] Hewlett, along with David Packard, co-founded Hewlett-Packard, and Hewlett-Packard's first product was the HP200A, a precision Wien bridge oscillator.
The frequency of oscillation is given by:
<math>f = \frac{1}{2 \pi R C}</math>
Contents
Background
Problems with a conventional oscillator
The conventional oscillator circuit is designed so that it will start oscillating ("start up") and that its amplitude will be controlled.
For a linear circuit to oscillate, it must meet the Barkhausen conditions: its loop gain must be one and the phase around the loop must be a multiple of 360 degrees. The linear oscillator theory doesn't address how the oscillator starts up or how the amplitude is determined. The linear oscillator can support any amplitude.
In practice, the loop gain is initially larger than unity. Random noise is present in all circuits, and some of that noise will be near the desired frequency. A loop gain greater than one allows the amplitude of frequency to increase exponentially each time around the loop. With a loop gain greater than one, the oscillator will start.
Ideally, the loop gain needs to be just a little bigger than one, but in practice, it is often significantly greater than one. A larger loop gain makes the oscillator start quickly. A large loop gain also compensates for gain variations with temperature and the desired frequency of a tunable oscillator. For the oscillator to start, the loop gain must be greater than one under all possible conditions.
A loop gain greater than one has a down side. In theory, the oscillator amplitude will increase without limit. In practice, the amplitude will increase until the output runs into some limiting factor such as the power supply voltage (the amplifier output runs into the supply rails) or the amplifier output current limits. The limiting reduces the effective gain of the amplifier. (The effect is called gain compression.) In a stable oscillator, the average loop gain will be one.
Although the limiting action stabilizes the output voltage, it has two significant effects: it introduces harmonic distortion and it affects the frequency stability of the oscillator.
The amount of distortion is related to the extra loop gain used for startup. If there's a lot of extra loop gain at small amplitudes, then the gain must decrease more at higher instantaneous amplitudes. That means more distortion.
The amount of distortion is also related to final amplitude of the oscillation. Although an amplifier's gain is ideally linear, in practice it is nonlinear. The nonlinear transcribing function can be viewed as a Taylor series. For small amplitudes, the higher order terms have little effect. For larger amplitudes, the nonlinearity is pronounced. Consequently, for low distortion, the oscillator's output amplitude should be a small fraction of the amplifier's dynamic range.
Bridge oscillator
Meacham proposed a bridge oscillator to address those problems.[2]
Instead of using limiting to set an average gain of 1 around the loop, Meacham proposed a circuit that would set the loop gain to one while the amplifier was still in its linear region. As a result, the distortion would be reduced and the frequency stability would be improved. Meacham designed a quartz crystal oscillator based on a Wheatstone bridge that was a significant improvement over earlier designs.
At the oscillator frequency, Meacham's design was a linear circuit with constant gain. Consequently, there was no distortion of the sine wave. (In practice, an amplifier is not perfectly linear, so there is some distortion, but that distortion is much less than the gain compression approach.)
LC versus RC oscillator
Hewlett's oscillator
High-gain differential amplifier with positive feedback. Wien bridge oscillator can be considered as a combination of a differential amplifier and a Wien bridge connected in the positive feedback loop between the op-amp output and differential input. At the oscillating frequency, the bridge is almost balanced and has very small transfer ratio. The loop gain is a product of the very high op-amp gain and the very low bridge ratio.[3]
Conventional RC oscillator
Low-gain single-ended amplifier with positive feedback. Rf, Rb and the op-amp compose a non-inverting amplifier with small gain of 1 + Rf/Rb ≈ 3. R1, R2, C1, C2 compose a bandpass filter. The band pass filter is connected to provide positive feedback at the frequency of oscillation. In the ideal situation, R1 = R2 = R, C1 = C2 = C and Rf/Rb = 2. Rb self heats and reduces the amplifier gain until the point is reached that there is just enough gain to sustain sinusoidal oscillation without over driving the amplifier.
Wien bridge
Bridge circuits were a common way of measuring component values by comparing them to known values. Often an unknown component would be put in one arm of a bridge, and then the bridge would be nulled by adjusting the other arms or changing the frequency of the voltage source. See, for example, the Wheatstone bridge.
The Wien bridge is one of many common bridges.[4] Wien's bridge is used for precison measurement of capacitance in terms of resistance and frequency.[5] It was also used to measure audio frequencies.
The Wien bridge does not require equal values of R or C. At some frequency, the reactance of the series Rc–Cc arm will be an exact multiple of the shunt Rd–Cd arm. If the two Ra and Rb arms are adjusted to the same ratio, then the bridge is balanced.
The bridge is balanced when:[6]
- <math>\omega^2 = {1 \over R_d R_c C_d C_c}</math> and <math> {C_d \over C_c} = {R_b \over R_a} - {R_c \over R_d}</math>
where ω is the radian frequency.
The equations simplify if one chooses Rc = Rd and Cc = Cd; the result is Rb = 2 Ra.
In practice, the values of R and C will never be exactly equal, but the equations above show that for fixed values in the c and d arms, the bridge will balance at some ω and some ratio of Rb/Ra.
Analysis
Analyzed from loop gain
According to Schilling,[3] the loop gain of the Wien bridge oscillator is given by
- <math> T = ( \frac { R_1 / (1 + sC_1 R_1) } {R_1 / (1 + sC_1 R_1) + R_2 + 1/(sC_2)} - \frac {R_b} {R_b + R_f } )A_0 \,</math>
where <math> A_0 \,</math> is the frequency-dependent gain of the op-amp. (Note, the component names in Schilling have been replaced with the component names in the figure.)
Schilling further says that the condition of oscillation is <math> T = 1 \,</math>. Which, assuming <math> R_1 = R_2 = R\,</math> and <math>C_1 = C_2 = C \,</math> is satisfied by
- <math> \omega = \frac {1} {R C} \rightarrow F = \frac {1} {2 \pi R C}\,</math>
and
- <math> \frac {R_f} {R_b} = \frac {2 A_0 + 3} {A_0 - 3} \,</math> with <math>\lim_{A_0\rightarrow \infin} \frac {R_f} {R_b} = 2 \, </math>
Another analysis, with particular reference to frequency stability and selectivity, will be found in Strauss (1970, p. 671) and Hamilton (2003, p. 449).
Amplitude stabilization
The key to Hewlett's low distortion oscillator is effective amplitude stabilization. The amplitude of electronic oscillators tends to increase until clipping or other gain limitation is reached. This leads to high harmonic distortion, which is often undesirable.
Hewlett used an incandescent bulb as a positive temperature coefficient (PTC) thermistor in the oscillator feedback path to limit the gain. The resistance of light bulbs and similar heating elements increases as their temperature increases. If the oscillation frequency is significantly higher than the thermal time constant of the heating element, the radiated power is proportional to the oscillator power. Since heating elements are close to black body radiators, they follow the Stefan-Boltzmann law.[dubious ] The radiated power is proportional to <math>T^4</math>, so resistance increases at a greater rate than amplitude. If the gain is inversely proportional to the oscillation amplitude, the oscillator gain stage reaches a steady state and operates as a near ideal class A amplifier, achieving very low distortion at the frequency of interest. At lower frequencies the time period of the oscillator approaches the thermal time constant of the thermistor element and the output distortion starts to rise significantly.
Light bulbs have their disadvantages when used as gain control elements in Wien bridge oscillators, most notably a very high sensitivity to vibration due to the bulb's microphonic nature amplitude modulating the oscillator output, and a limitation in high frequency response due to the inductive nature of the coiled filament. Modern Wien bridge oscillators have used other nonlinear elements, such as diodes, thermistors, field effect transistors, or photocells for amplitude stabilization in place of light bulbs. Distortion as low as 0.0003% (3 ppm) can be achieved with modern components unavailable to Hewlett.[7]
Wien bridge oscillators that use thermistors also exhibit "amplitude bounce" when the oscillator frequency is changed. This is due to the low damping factor and long time constant of the crude control loop, and disturbances cause the output amplitude to exhibit a decaying sinusoidal response. This can be used as a rough figure of merit, as the greater the amplitude bounce after a disturbance, the lower the output distortion under steady state conditions.
See also
- Armstrong oscillator
- Clapp oscillator
- Colpitts oscillator
- Hartley oscillator
- Relaxation Oscillator
- Vačkář oscillator
Notes
Cite error: Invalid <references>
tag;
parameter "group" is allowed only.
<references />
, or <references group="..." />
References
- Bauer, Brunton (November 1949), "Design Notes on the Resistance-Capacity Oscillator Circuit (Part I)" (PDF), Hewlett-Packard Journal, Hewlett-Packard Company, 1 (3)
- Bauer, Brunton (December 1949), "Design Notes on the Resistance-Capacity Oscillator Circuit (Part II)" (PDF), Hewlett-Packard Journal, Hewlett-Packard Company, 1 (4)
- Ferguson, J. G.; Bartlett, B. W. (July 1928), "The Measurement of Capacitance in Terms of Resistance and Frequency" (PDF), Bell System Technical Journal, 7 (3): 420–437
- Hamilton, Scott (2003), An Analog Electronics Companion: basic circuit design for engineers and scientists, Cambridge University Press, ISBN 9780521798389
- Hamilton, Scott (2007), An Analog Electronics Companion: basic circuit design for engineers and scientists and introduction to SPICE simulation, Cambridge University Press, ISBN 9780521687805
- US 2268872, Hewlett, William R., "Variable Frequency Oscillation Generator", published July 11, 1939, issued January 6, 1942
- Meacham, L. A. (October 1938), "The Bridge Stabilized Oscillator" (PDF), Bell System Technical Journal, 17 (4): 574–591. Frequency and amplitude stabilization of an oscillator with no tube overloading. Uses tungsten lamp to balance bridge.
- Oliver, Bernard M. (April–June, 1960), "The Effect of μ-Circuit Non-Linearity on the Amplitude Stability of RC Oscillators" (PDF), Hewlett-Packard Journal, 11 (8-10): 1–8 Check date values in:
|date=
(help). Shows that amplifier non-linearity is needed for fast amplitude settling of the Wien bridge oscillator. - Schilling, Donald; Belove, Charles (1968), Electronic Circuits: Discrete and Integrated, McGraw-Hill
- Strauss, Leonard (1970), Wave Generation and Shaping (2nd ed.), McGraw-Hill, ISBN 978-0070621619
- Terman, Frederick (1943), Radio Engineers' Handbook, McGraw-Hill
- Wien, M. (1891), "Messung der Inductionsconstanten mit dem "optischen Telephon" (Measurement of Inductive Constants with the "Optical Telephone")", Annalen der Physik und Chemie (in German), 280 (12): 689–712, doi:10.1002/andp.18912801208
- Williams, Jim (June 1990), Bridge Circuits: Marrying Gain and Balance, Application Note, 43, Linear Technology Inc, pp. 29–33, 43
- Williams, Jim, ed. (1991), Analog Circuit Design, Art, Science, and Personalities, Butterworth Heinemann, ISBN 0750696400
External links
- Model 200A Audio Oscillator, 1939, HP Virtual Museum.
- Circuit Analysis, including SPICE simulation.
- Wien Bridge Oscillatorda:Wienbro-oscillator
de:Wien-Robinson-Brücke es:Oscilador de puente de Wien eu:Wienen zubi fr:Pont de Wien it:Oscillatore a ponte di Wien pt:Ponte de Wien ru:Генератор с мостом Вина
zh:文氏电桥- ↑ Wien 1891
- ↑ Meacham 1938
- ↑ 3.0 3.1 Schilling (1968, pp. 612–614)
- ↑ Terman 1943, p. 904
- ↑ Terman 1943, p. 904 citing Ferguson & Bartlett 1928
- ↑ Terman 1943, p. 905
- ↑ Williams (1990, pp. 32–33)
- Pages with broken file links
- All articles with unsourced statements
- Articles with unsourced statements from August 2011
- Articles with invalid date parameter in template
- All accuracy disputes
- Articles with disputed statements from August 2011
- 2Fix
- CS1 errors: dates
- CS1 maint: Unrecognized language
- Oscillators
- Analog circuits
- Electronic test equipment