Hobbing
Hobbing is a machining process for making gears, splines, and sprockets on a hobbing machine, which is a special type of milling machine. The teeth or splines are progressively cut into the workpiece by a series of cuts made by a cutting tool called a hob. Compared to other gear forming processes it is relatively inexpensive but still quite accurate, thus it is used for a broad range of parts and quantities.[1]
It is the most widely used gear cutting process for creating spur and helical gears[2] and more gears are cut by hobbing than any other process since it is relatively quick and inexpensive.[3]
Contents
Process
Hobbing uses a hobbing machine with two non-parallel spindles, one mounted with a blank workpiece and the other with the hob. The angle between the hob's spindle and the workpiece's spindle varies, depending on the type of product being produced. For example, if a spur gear is being produced, then the hob is angled equal to the helix angle of the hob; if a helical gear is being produced then the angle must be increased by the same amount as the helix angle of the helical gear.[4] The two shafts are rotated at a proportional ratio, which determines the number of teeth on the blank; for example, if the gear ratio is 40:1 the hob rotates 40 times to each turn of the blank, which produces 40 teeth in the blank. Note that the previous example only holds true for a single threaded hob; if the hob has multiple threads then the speed ratio must be multiplied by the number of threads on the hob.[5] The hob is then fed up into workpiece until the correct tooth depth is obtained. Finally the hob is fed into the workpiece parallel to the blank's axis of rotation.[4]
Up to five teeth can be cut into the workpiece at the same time.[3] Oftentimes multiple gears are cut at the same time.[5]
For larger gears the blank is usually gashed to the rough shape to make hobbing easier.
Equipment
Modern hobbing machines, also known as hobbers, are fully automated machines that come in many sizes, because they need to be able to produce anything from tiny instrument gears up to 10 ft (3.0 m) diameter marine gears. Each gear hobbing machine typically consists of a chuck and tailstock, to hold the workpiece or a spindle, a spindle on which the hob is mounted, and a drive motor.[3]
For a tooth profile which is a theoretical involute, the fundamental rack is straight-sided, with sides inclined at the pressure angle of the tooth form, with flat top and bottom. The necessary addendum correction to allow the use of small-numbered pinions can either be obtained by suitable modification of this rack to a cycloidal form at the tips, or by hobbing at other than the theoretical pitch circle diameter. Since the gear ratio between hob and blank is fixed, the resulting gear will have the correct pitch on the pitch circle, but the tooth thickness will not be equal to the space width.
Hobbing machines are characterised by the largest module or pitch diameter it can generate. For example, a 10 in (250 mm) capacity machine can generate gears with a 10 in pitch diameter and usually a maximum of a 10 in face width. Most hobbing machines are vertical hobbers, which means the blank is mounted vertically. Horizontal hobbing machines are usually used for cutting longer workpieces; i.e. cutting splines on the end of a shaft.[6]
Hob
The hob is the cutter used to cut the teeth into the workpiece. It is cylindrical in shape with helical cutting teeth. These teeth have grooves that run the length of the hob, which aid in cutting and chip removal. There are also special hobs designed for special gears such as the spline and sprocket gears.[3]
The cross-sectional shape of the hob teeth are almost the same shape as teeth of a rack gear that would be used with the finished product. There are slight changes to the shape for generating purposes, such as extending the hob's tooth length to create a clearance in the gear's roots.[7] Each hob tooth is relieved on the back side to reduce friction.[8]
Most hobs are single-thread hobs, but double-, and triple-thread hobs increase production rates. The downside is that they are not as accurate as single-thread hobs.[9]
This list outlines types of hobs:
- Roller chain sprocket hobs
- Worm wheel hobs
- Spline hobs
- Chamfer hobs
- Spur and helical gear hobs
- Straight side spline hobs
- Involute spline hobs
- Serration hobs
- Semitopping gear hobs
Uses
Hobbing is used to make following types of finished goods:
- Cycloid gears (see below)
- Helical gears
- Involute gears
- Ratchets
- Splines
- Sprockets
- Spur gears
- Worm gears
Hobbing is used to produce most throated worm wheels, but certain tooth profiles cannot be hobbed. If any portion of the hob profile is perpendicular to the axis then it will have no cutting clearance generated by the usual backing off process, and it will not cut well.
Cycloidal forms
For cycloidal gears (as used in BS978-2 Specification for fine pitch gears) and cycloidal-type gears each module, ratio and number of teeth in the pinion requires a different hobbing cutter so the technique is only suitable for large volume production.
To circumvent this problem a special war-time emergency circular arc gear standard was produced giving a series of close to cycloidal forms which could be cut with a single hob for each module for eight teeth and upwards to economize on cutter manufacturing resources. A variant on this is still included in BS978-2a (Gears for instruments and clockwork mechanisms. Cycloidal type gears. Double circular arc type gears).
Tolerances of concentricity of the hob limit the lower modules which can be cut practically by hobbing to about 0.5 module.
History
Many manufacturing firms that maintain museums of how products were produced in times past will have examples of manual gear hobs that helped to produce gears prior to the gears of the 19th century and earlier. Along with these completely manual gear hobs will be samples of some of the first semi-automated gear hobs, and finally examples of more recent technology that demonstrates the fully automated process that modern gear hobs use to produce gears today. A few producers of gear hobs also have interesting literature on the history of gear hobs, including details about how modern gear hobs can produce thousands of gears in a single hour.
See also
References
Cite error: Invalid <references> tag;
parameter "group" is allowed only.
<references />, or <references group="..." />Bibliography
- American Society for Metals; Cubberly, William H.; Bardes, Bruce P. (1978), Metals Handbook: Machining, 16 (9th, Illustrated ed.), ASM International, ISBN 9780871700070.
- Degarmo, E. Paul; Black, J T.; Kohser, Ronald A. (2003), Materials and Processes in Manufacturing (9th ed.), Wiley, ISBN 0-471-65653-4.
- Drozda, Tom; Wick, Charles; Benedict, John T.; Veilleux, Raymond F.; Society of Manufacturing Engineers; Bakerjian, Ramon (1983), Tool and Manufacturing Engineers Handbook: Machining, 1 (4th, illustrated ed.), Society of Manufacturing Engineers, ISBN 9780872630857.
- Endoy, Robert (1990), Gear hobbing, shaping, and shaving (Illustrated ed.), Society of Manufacturing Engineers, ISBN 9780872633834.
- Jones, Franklin D. (1964), Machine Shop Training Course (5th, Illustrated ed.), Industrial Press Inc., ISBN 9780831110406.
- Todd, Robert H.; Allen, Dell K.; Alting, Leo (1994), Manufacturing Processes Reference Guide, Industrial Press Inc., ISBN 0-8311-3049-0.
- ↑ American Society for Metals, Cubberly & Bardes 1978, p. 334.
- ↑ Drozda et al., p. 13-34.
- ↑ 3.0 3.1 3.2 3.3 Todd, Allen & Alting 1994, pp. 59–60.
- ↑ 4.0 4.1 Degarmo, Black & Kohser 2003, p. 769.
- ↑ 5.0 5.1 Jones 1964, p. 289.
- ↑ Endoy 1990, p. 6.
- ↑ Jones 1964, p. 288.
- ↑ Degarmo, Black & Kohser 2003, p. 768.
- ↑ Degarmo, Black & Kohser 2003, p. 770.
